PROSES PENGUJIAN ULTRASONIC TESTING (UT) DALAM MENDETEKSI CACAT LAMINASI

.

Authors

  • Daniel Sutopo Pamungkas Program Studi Teknik Elektro, Politeknik Negeri Batam
  • Nugroho Pratomo Ariyanto Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Ari Wibowo Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Muhammad Ismail Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Yosef Adicita Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Reza Apriyono Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Roza Puspita Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Muhammad Ilham Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
  • Nurul Laili Arifin Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam

Keywords:

Non-Destructive test, Lamination Testing, Ultrasonic Testing, Quality Control

Abstract

Non-Destructive Testing (NDT) is an essential part of quality control that plays a role in verifying that a material is in good condition and suitable for use. One of the most widely applied NDT methods is Ultrasonic Testing (UT), a versatile inspection technique that can be used on a wide range of products. This study aims to apply the Ultrasonic Testing (UT) method based on the ISO 7963:2022 calibration block standard to detect and identify the presence of lamination defects in materials and to evaluate its reliability in the inspection process. The probe used in this study was a normal probe (straight beam probe) with a frequency range of 1 to 6 MHz. The testing procedure was carried out in accordance with ISO 16810, while the calibration method followed the requirements specified in ISO 7963:2022.Based on the testing conducted in accordance with the ISO 7963:2022 standard, several defect indications were detected at depths ranging from 14.7 mm to 15.05 mm, with a minimum amplitude of ≥ 40% Full Screen Height (FSH). Overall, the test results showed a UT equipment deviation of only 0.1%, indicating that the method provides excellent accuracy and can be reliably applied in material inspection processes.

Downloads

Download data is not yet available.

References

[1] B. Wang, S. J. Hu, L. Sun, and T. Freiheit, “Intelligent welding system technologies: State-of-the-art review and perspectives,” J. Manuf. Syst., vol. 56, pp. 373–391, Jul. 2020, doi: 10.1016/j.jmsy.2020.06.020.

[2] A. Raj et al., “RETRACTED ARTICLE: Weld quality monitoring via machine learning-enabled approaches,” Int. J. Interact. Des. Manuf. IJIDeM, Jan. 2023, doi: 10.1007/s12008-022-01165-9.

[3] M. Shaloo, M. Schnall, T. Klein, N. Huber, and B. Reitinger, “A Review of Non-Destructive Testing (NDT) Techniques for Defect Detection: Application to Fusion Welding and Future Wire Arc Additive Manufacturing Processes,” Materials, vol. 15, no. 10, p. 3697, May 2022, doi: 10.3390/ma15103697.

[4] P. Kah, R. Rajan, J. Martikainen, and R. Suoranta, “Investigation of weld defects in friction-stir welding and fusion welding of aluminium alloys,” Int. J. Mech. Mater. Eng., vol. 10, no. 1, p. 26, Dec. 2015, doi: 10.1186/s40712-015-0053-8.

[5] T. Endramawan and A. Sifa, “APLIKASI STANDAR AWS UNTUK MENENTUKAN ACCEPTANCE CRITERIA PADA PENGELASAN SMAW MENGGUNAKAN NONDESTRUCTIVE TEST-ULTRASONIC TEST,” Turbo J. Program Studi Tek. Mesin, vol. 6, no. 2, Dec. 2017, doi: 10.24127/trb.v6i2.544.

[6] S. Tavares, K. Yang, and M. A. Meyers, “Heusler alloys: Past, properties, new alloys, and prospects,” Prog. Mater. Sci., vol. 132, p. 101017, Feb. 2023, doi: 10.1016/j.pmatsci.2022.101017.

[7] M. V. Felice and Z. Fan, “Sizing of flaws using ultrasonic bulk wave testing: A review,” Ultrasonics, vol. 88, pp. 26–42, Aug. 2018, doi: 10.1016/j.ultras.2018.03.003.

[8] M. Mihaljević, H. Cajner, B. Runje, D. Markučič, and Z. Keran, “Analysis of the couplant influence on the ultrasonic thickness measurement of the steel grade S355J0: Untersuchung des Einflusses des Koppelmittels auf die Ultraschall-Messung der Probendicke des Stahls S355J0,” Mater. Werkst., vol. 48, no. 8, pp. 803–813, Aug. 2017, doi: 10.1002/mawe.201700050.

[9] K. Schabowicz, “Non-Destructive Testing of Materials in Civil Engineering,” Materials, vol. 12, no. 19, p. 3237, Oct. 2019, doi: 10.3390/ma12193237.

[10] S. Hassani and U. Dackermann, “A Systematic Review of Advanced Sensor Technologies for Non-Destructive Testing and Structural Health Monitoring,” Sensors, vol. 23, no. 4, p. 2204, Feb. 2023, doi: 10.3390/s23042204.

[11] Y. Chen, J. Zhang, A. J. Croxford, and P. D. Wilcox, “Thickness measurement optimisation for permanently installed inductively coupled ultrasonic transducer systems,” NDT E Int., vol. 129, p. 102655, Jul. 2022, doi: 10.1016/j.ndteint.2022.102655.

[12] P. J. Shull, Nondestructive Evaluation, 0 ed. CRC Press, 2002. doi: 10.1201/9780203911068.

[13] A. Hidayatullah, M. F. Muvariz, H. Saputra, W. Rossbandrio, and N. Yuniarsih, “Studi Replating Area Forepeak & Deep Tank pada Kapal Tanker 105 Meter Berdasarkan Hasil Pengujian Ultrasonic Thickness Test,” J. Teknol. Dan Ris. Terap. JATRA, vol. 5, no. 1, pp. 1–8, Jun. 2023, doi: 10.30871/jatra.v5i1.3655.

[14] A. Fajrin, M. Mutiarani, N. P. Ariyanto, and W. Wissesa, “Identifikasi Tebal Plat Lambung Kapal Tanker Tyche IMO 8794891 Dengan Ultrasonic Thicness Gauge,” J. Teknol. Dan Ris. Terap. JATRA, vol. 4, no. 2, pp. 69–73, Dec. 2022, doi: 10.30871/jatra.v4i2.4786.

[15] F. Widyawati and L. Marano, “IDENTIFIKASI CACAT LASAN FCAW PADA FONDASI MESIN KAPAL MENGGUNAKAN METODE ULTRASONIC TESTING,” J. TAMBORA, vol. 5, no. 2, pp. 53–58, Jul. 2021, doi: 10.36761/jt.v5i2.1124.

[16] H. Darmadi, A. B. Tarigan, U. I. Purba, N. S. Bintang, R. Faulianur, and D. Kurnia, “ANALISA KETEBALAN DINDING SHELL (SPLITTING) DENGAN METODE PENGUKURAN TEMPERATUR TINGGI MENGGUNAKAN ALAT ULTRASONIC THICKNESS PADA FATTY ACID PLANT DI PT XYZ,” J. Tek. Mesin, 2025.

[17] L. E. Maggi, C. E. R. Silva, A. V. Alvarenga, and R. P. B. Costa-Felix, “Ultrasonic calibration and certification of V1 and V2 type reference standard blocks for use in Non-Destructive Testing,” J. Phys. Conf. Ser., vol. 279, p. 012029, Feb. 2011, doi: 10.1088/1742-6596/279/1/012029.

[18] R. A. Pitalokha, C. Mulyana, M. R. Hamdani, and F. Muhammad, “INSPEKSI CACAT (DISKONTINUITAS) PADA MATERIAL DENGAN MENGGUNAKAN UJI ULTRASONIK DAN UJI RADIOGRAFI,” in PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016 UNJ, Pendidikan Fisika dan Fisika FMIPA UNJ, 2016, pp. SNF2016-MPS-29-SNF2016-MPS-36. doi: 10.21009/0305020206.

[19] P. Pujono and E. W. Galih, “Inspeksi Upper Wing Top Skin Panel Menggunakan Phased Array Ultrasonic Testing (PAUT),” Bangun Rekaprima, vol. 4, no. 2, p. 65, Oct. 2018, doi: 10.32497/bangunrekaprima.v4i2.1202.

[20] T. T. Widodo, D. A. Kifta, R. Yasra, and R. Suhadi, “Analisa Pengendalian Kualitas Scanning Data Phased Array Ultrasonic Testing (PAUT) Untuk Meningkatkan Produksi”.

Downloads

Published

2026-06-28

How to Cite

Pamungkas, D. S., Pratomo Ariyanto , N., Wibowo, A., Ismail, M., Adicita, Y., Apriyono, R., … Arifin, N. L. (2026). PROSES PENGUJIAN ULTRASONIC TESTING (UT) DALAM MENDETEKSI CACAT LAMINASI: . Jurnal Teknologi Dan Riset Terapan (JATRA), 8(1), 73–79. Retrieved from https://jurnal.polibatam.ac.id/index.php/JATRA/article/view/12990

Issue

Vol. 8 No. 1 (2026): Jurnal Teknologi Dan Riset Terapan (JATRA) - Juni 2026

Section

Research Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Most read articles by the same author(s)