Pengaruh Jumlah Mata Sayat Flute End Milling Cutting Terhadap Kualitas Permukaan Austenite Stainless Steel (ASS) 304

  • Hendra Butar Butar Program Studi Teknik Mesin, Politeknik Negeri Batam
  • Rahman Hakim Program Studi Teknik Mesin, Politeknik Negeri Batam
  • Windy Stefani Program Studi Teknik Mesin, Politeknik Negeri Batam
  • Saiful Arif Jurusan Teknik Mesin, Politeknik Negeri Malang
  • Nugroho Pratomo Ariyanto Program Studi Teknik Mesin, Politeknik Negeri Batam
Keywords: CNC Milling Machine, Surface Roughness, Number of flutes, Austenitic Stainless Steel, Machining Process

Abstract

The working principle of CNC Milling machine is the machine rotates and contacts with the workpiece so that erosion and cutting occur. The machining process affects the mechanical properties of the material, so it needs to conduct a study to determine changes in the character of the material due to the machining process. This research was conducted to determine the effect of the number of 2 flutes and 4 flutes on the workpiece surface roughness using PMC-5VT20 CNC Milling machine. Specimens test use 304 material stainless steel that has strength and resistance to the corrosive. The research method was carried out experimentally using 304 stainless steel material which had been done with a finishing process using an endmill cutter with 2 flutes and 4 flutes. The roughness of specimens were tested using surface roughness tester to determain the effect of  flute number on the surface roughness. The result of testing shows that the number of flutes affects the roughness of the machining process. The roughness value using 2 flutes is lower than the use of 4 flutes.

Downloads

Download data is not yet available.

References

A. Aryswan, R. Hakim, and M. Saputra, “Analisa Kekasaran Permukaan Produk Mesin Cetak Tiga Dimensi Dengan Material Acrylonitrile Butadiene Styrene Terlapis Cat Emulsi”, JATRA, vol. 1, no. 2, pp. 72-75, Dec. 2019.

Arif, S. 2017 Kediri: Multitek Indonesia Jurnal Ilmiah, Vol. 11, No. 2, Desember, 2017.

Anshori, Mohammad dkk. Tidak diketahui, “Analisis Perbandingan Kekasaran Permukaan Pada Proses Turning.” Malang: Jurnal Teknik Mesin, Universitas Islam Malang, 9 November 2013.

Achmadarifin.com, “Jenis batu gerinda berdasarkan bahan asah dan tingkat kekerasannya”, 12 April 2018, < http://achmadarifin.com/jenis-batu-gerinda > diakses pada 2 November 2019.

E-rigging.com, “Materials-and-Finishes-to-Combat-Corrosion”, 1 Mei 2018, < http://www.e-rigging.com/Materials-and-Finishes-to-Combat-Corrosion> diakses pada 2 November 2019.

Fundamental of CNC Machining. 2014. Library of Congress : USA.

Logamceper.com, “Karakteristik Stainless Steel”, 1 April 2016, < https://logamceper.com/karakteristik-stainless-steel/ > diakses pada 2 November 2019.

Irwan, Mohammad., Tidak diketahui, “Pengaruh Kecepatan Putar Alat Potong (Spindle Speed) dan Kedalaman Pemakanan (Depth Of Cut) Proses Milling pada Aluminium Alloy Terhadap Kehalusan Permukaan Produk.” Batam: Jurnal Politeknik Negeri Batam.

Pudji, E.P.,& Pilarian, P. 2013, “Optimasi Parameter Proses Pemotongan Stainless Steel Sus 304 Untuk Kekasaran Permukaan Dengan Metode Response Surface.” Yogyakarta: Seminar Nasional Matematika dan Pendidikan Matematika FMIPA UNY, Yogyakarta, 9 November 2013.

Published
2023-06-30
How to Cite
Butar Butar, H., Hakim, R., Stefani, W., Arif, S., & Ariyanto, N. (2023). Pengaruh Jumlah Mata Sayat Flute End Milling Cutting Terhadap Kualitas Permukaan Austenite Stainless Steel (ASS) 304. Jurnal Teknologi Dan Riset Terapan (JATRA), 5(1), 16-20. https://doi.org/10.30871/jatra.v5i1.4870

Most read articles by the same author(s)

<< < 1 2