Kendali Motor Stepper pada Fast Shot & Slow Shot Valve Die Casting Machine Menggunakan PLC Omron

Abdillah Aziz Muntashir; Muhammad Ario Rizky; Muhammad Samhadi Nugroho

doi:10.30871/ji.v15i2.6506

Abdillah Aziz Muntashir Politeknik Astra https://orcid.org/0000-0001-8450-1045
Muhammad Ario Rizky Politeknik Astra
Muhammad Samhadi Nugroho Politeknik Astra

DOI: https://doi.org/10.30871/ji.v15i2.6506

Keywords: HMI Omron NB7W-TW00B, Stepper Motor Nema 17, PLC Omron CP1L-M30DT-D

Abstract

In producing a product in the industry, it is necessary to pass a series of processes, one of which is in the printing process or die casting. After installation of casting molds (Fix Dies & Moving Dies), it is necessary to set the fast shot & slow shot valve rotation to determine the amount that pushes the molten liquid into the mold, so the casting machine is ready to use. At this time the Fast Shot & Slow Shot Valve setting process is still done manually (conventional), the technician must make a rotation manually and only look at the value of the needle available on the knob, therefore we need a modification on the control system that can facilitate in doing setting the valve. By using the Stepper motor Nema 17 as the output of the Omron CP1L-M30DT-D PLC and also using Encoder E6B2-CWZ6C as an input that has been calibrated, so that the round reading can be seen in HMI Omron NB7W-TW00B. Obtained a fast cycle time results, namely in moving 1 round of knob, it takes 0.6 seconds.

Downloads

Download data is not yet available.

References

S. N. Susianti, “Analisis Perawatan Mesin Casting Zinc Menggunakan Metode Overall Equipment Effectivness (OEE) Melalui Pendekatan DMAIC,” JENIUS J. Terap. Tek. Ind., vol. 1, no. 1, pp. 30–37, 2020.

R. Aulia, R. A. Fauzan, and I. Lubis, “Pengendalian Suhu Ruangan Menggunakan Menggunakan FAN dan DHT11 Berbasis Arduino,” CESS (Journal Comput. Eng. Syst. Sci., vol. 6, no. 1, p. 30, 2021.

M. Han, Y. Liu, D. Wu, H. Tan, and C. Li, “Numerical Analysis and Optimisation of the Flow Forces in a Water Hydraulic Proportional Cartridge Valve for Injection System,” IEEE Access, vol. 6, pp. 10392–10401, 2018.

F. H. Utomo, “Komponen PLC dan fungsinya,” 2022.

Ferdiyansyah, Yafta Qisti, and Dibyo Setiawan. "Analisis Sistem Manajemen Pemeliharaan Mesin Die Casting." Engineering and Technology International Journal. vol 02, pp 138-143, 2023.

Djalmono, Wahyu, Ampala Khoryanton, and Ikhsan Muzaki. "Sistem Pendingin Menggunakan Thermalelectric Cooler Guna Menstabilkan Temperatur Box Panel Kontrol Mesin Die Casting." Jurnal Rekayasa Mesin . vol 3, pp 146-156, 2019.

Andriani, Andriani, and Ikhsan Romli. "Preventive maintenance pada mesin die casting dengan age replacement model untuk peningkatan reliabilitas mesin." Oper. Excell. J. Appl. Ind. Eng. Vol 12, pp 1-12, 2020.

Nurjanah, Susianti. "Analisis Perawatan Mesin Casting Zinc Menggunakan Metode Overall Equipment Effectivness (OEE) Melalui Pendekatan DMAIC." JENIUS: Jurnal Terapan Teknik Industri vol 1.1, pp 30-37, 2020

Widodo, Joko Sri, Taufiqur Rokhman, and R. Hengki Rahmanto. "SEMINAR MENGENAI PROSES PEMBUATAN SPARE PARTS OTOMOTIF MELALUI PROSES DIE CASTING PADA SISWA SMK KARYA GUNA 1 BEKASI." An-Nizam, vol 1, pp 87-91, 2022.

Wibowo, Budi Cahyo, and Fajar Nugraha. "Stepper Motor Speed Control Using Start-Stop Method Based On PLC." J. Tek. Elektro dan Komput. UNSRAT , vol 10, pp 213-220, 2021.

Khoirurrizal, M. RANCANG BANGUN MINIATUR LIFT 3 LANTAI MENGGUNAKAN PLC OMRON CP1E DENGAN HMI. Diss. Universitas Sultan Agung, 2021.