Rancang Bangun Digital Firing Angle Sebagai AC – AC Controller Untuk Alat Pengering Sepatu Dengan Metode Kontrol Proporsional Integral

  • Mochamad Ari Bagus Nugroho Politeknik Elektronika Negeri Surabaya
  • Hasnira Hasnira Politeknik Negeri Batam
  • Mohammad Zainul Iraqi Politeknik Elektronika Negeri Surabaya
  • Suhariningsih Suhariningsih Politeknik Elektronika Negeri Surabaya

Abstract

The rainy season is an obstacle for everyone, especially drying shoes, because rain can hinder the process of drying shoes. Currently, shoes are still dried using the conventional method, namely by utilizing the sun's heat. The next development is a system for drying shoes using gas fuel, but it has the potential for fire. In this final project, a shoe drying system is designed which is controlled using PI control according to a specified setpoint to dry shoes when exposed to rain or at night. To get the appropriate room temperature, the output voltage from the heater needs to be controlled using the Digital Firing Angle. The ignition angle is regulated by the Digital Firing Angle circuit. To maintain the temperature conditions in a stable condition, namely 65°C, this tool is controlled using PI (Proportional Integral) control. This dryer is designed for a maximum of 1 pair of wet shoes. With final humidity results in the drying room ≤ 20%RH. With this final project, it can dry shoes in rainy conditions in 94 minutes for synthetic leather shoes and 104 minutes for leather shoes.

Downloads

Download data is not yet available.

References

Sugitantoei and B. Nehemia, Analisis Laju Pengeringan Pada Alat Pengering Pakaian Dengan Bahan Bakar Kompor LPG. Malang: Institut Teknologi Nasional, 2020.

D. Y. Oktara, Suhariningsih, and F. D. Murdianto, Desain dan Implementasi Alat Pengering Baju Otomatis Menggunakan Kontrol PI. Surabaya: Politeknik Elektronika Negeri Surabaya, 2022

R. G. Afriandi, Sistem Kendali Pengering Sepatu Berbasis Arduino. Kudus: Universitas Muria Kudus, 2020.

A. B. Rizkianto, Rancang Bangun Pengering Sepatu Berdasarkan Kelembaban Menggunakan Metode PID. Surabaya: Institut Bisnis dan Informatika STIKOM, 2019.

F. Puspasari, T. P. Satya, U. Y. Oktiawati, I. Fahrurrozi, and H. Prisyanti, “Analisis Akurasi Sistem Sensor DHT22 berbasis Arduino terhadap Thermohygrometer Standar,” Jurnal Fisika dan Aplikasinya (JFA), vol.16, no.1, pp. 1-2, 2020.

I. Ferdiansyah, Irianto, and E. Sunarno, “Penerapan Kontrol PI Pada Alat Pengaduk dan Pengukus Adonan Pudak untuk Meningkatkan Hasil Produksi Industri Rumah Tangga di Gresik”, Jurnal Teknologi Terpadu (JTT), vol. 8, no.2, pp. 4, 2020.

I. Ferdiansyah, L. P. S. Raharja, D. S. Yanaratri and E. Purwanto, “Design of PID Controller for Speed Control of Three Phase Induction Motor Based on Direct-Axis Current (Id) Coordinate Using IFOC,” in 4th International Conference on Information Technology, Information System and Electrical Engineering (ICITISEE), Yogyakarta, Indonesia, 2018.

P. Jin, M. Zheng, B. Qi and D. Feng, “Heating speed control method based on adaptive fuzzy PID Algorithm,” in IEEE Conference on Industrial Electronics and Applications (ICIEA), Wuhan, China, 2018.

H. Yudianto, Perancangan Sistem Kontrol PID Menggunakan Simulink. Surabaya: Politeknik Elektronika Negeri Surabaya, 2012.

W. Priyade, Analisis dan Desain Kontrol PID Pada Kecepatan Motor DC Berbasis NI MYRIO. Malang: Universitas Muhammadiyah Malang, 2018.

Published
2024-03-27

Most read articles by the same author(s)

<< < 1 2